Monday, September 20, 2010

Moving the focus point can affect flash output !

Update: This issue has been fixed with the newer bodies as I found while doing the same test with the D7200, the difference being that with the D7200 the meter changes once the flash is turned on unlike the D90. This is the result I got in June 2016. The D7200 did not do this.

First off : This is not a big cause for concern when using TTL-BL or wireless CLS , it is just an exercise in understanding how TTL-BL 'thinks' and very hard to duplicate in a test scene let alone have the possibility of it happening during normal photography :) .
I decided to 'correct' an incorrect blog on the subject .
I'll just emphasize here that the flash does not meter off the selected focus point , the change has nothing to do with the way the flash system meters .
This will also only happen in TTL-BL mode and with Nikon's CLS wireless flash which also meters in TTL-BL mode . The possibility of it happening falls within a very small window of the metering system - when the meter detects under-exposure causing the flash system to compensate by increasing output , or conversely by decreasing output if it detects that the exposure is suddenly correct after it showing as being under-exposed .
The possibility of this happening when a focus point is moved also depends heavily on the metering mode selected [ it must be matrix metering ] and how matrix metering works in that particular body - because it varies between models .
I used the Nikon D90 in these tests , I've tested the matrix metering system before and understand [ to a degree] how it 'thinks' .
In many of the Nikon's [ not too sure about Canon ] matrix metering is strongly weighted toward the selected focus point and the 'focus plane' that it sits on , and it adjusts exposure accordingly . 
This means that if you are photographing a landscape and move the focus point from bright sky to shadow area "in the same frame" your exposure could vary by as much as two stops without even moving the camera .


Now it has been suggested that the changes seen in flash output are not due to the metering but rather due to the change in distance info from the lens which affect the output of TTL-BL flash [ not wireless which doesn't use the distance info ] .
This will cause changes as well but not the type I am demonstrating here . I have selected a scene in which the darker object which causes the an increase in output , is actually closer than the lighter object proving that the change in this case is not related to distance info from the lens .


Here is my test scene , the back of a camera closer to the camera with a white multi-plug adapter further back . 


Theoretically  when I change the focus point from the white object to the black object closer to the camera the flash exposure should decrease as the lens registers a closer focus point .


First I take a picture with the focus point moved onto the white object :




Then I move it onto the black object closer to the camera .... the flash exposure increases !?!




Why did that happen ?
Well TTL-BL and wireless CLS 'watch your meter" and adjust output accordingly .
Here's the back of the screen in the first shot : 
The camera's meter was happy with the exposure with the focus point on the white object - that 'focus plane' decided that the camera's settings were correct for the scene so the camera told the flash to back off accordingly .




After taking the picture I simply moved the focus point onto the black object closer to the camera , which should have backed off the flash according to the distance info , but when the 'focus plane' shifted and the white object was no longer a dominant part of matrix metering's equation it decided that the image was under-exposed and the meter moved to "-1"
No camera settings were changed , the focus point was simply moved .


The flash output was increased because matrix metering decided that the scene , for that focus point , was under-exposed and so it decided to increase the flash output accordingly !
So this proves that regardless of the changes caused by the distance information from the lens , there are isolated instances where flash output can be affected by moving the focus point in the same scene with no other changes to the camera's settings :) .











6 comments:

Unknown said...

Hello Desmond, just wandering around your blog and find it fascinating. No doubt I'll be asking questions on other blog posts you've made. For now a question or three about this particular post.

First...do you now use BL exclusively or are there times when you use other flash modes?

Second...in this blog post you used exclamation points relating to the brightening of the camera black once the focus point was placed upon it. Is this not a surprise? The camera meters such that an average exposure is achieved. Therefore, black objects cause the meter to increase exposure which may or may not be correct for the photographer. To render that darker subject correctly, ie darker, some degree of negative compensation is required. My understanding is that flash, BL or not, mirrors the camera meter and it's own sensor and will again fire harder than maybe required. So, negative flash compensation required.

Third...Following point two above, if I use BL and factor in minus compensation on camera, will BL follow that and fire at a lower level of power? Here I'm thinking the subject backlit on a bright day and metering for the ambient. In camera dropping the ambient by say 1.5 stops. Does BL follow that and provide an appropriate level of power incorporating the -1.5 stops in camera? Or would I need to compensate that -1.5 in camera stops with +stops with flash exposure compensation?

Thank you
Paul

Desmond Downs said...

Hi Paul , thanks for the questions and input .
1.) I do only use TTL-BL now . No flash system is perfect but TTL-BL is the most consistent for me .

2.) Yes , obviously the metering increases exposure when it sees the subject as being darker and appropriate exposure compensation would be needed . The primary purpose of this particular discussion is the fact that TTL-BL flash exposure can change "in the same scene" simply by moving the focus point since 3D matrix metering exposes strongly toward the part of the scene under the focus point - and yes , TTL-BL reacts accordingly when it notices the meter drop .

3.) Regarding exposure compensation on the camera , the flash will also adjust proportionately . "-1" EV will also drop the flash to "-1" ."-1" on the body and "+1" on the flash will give the same flash exposure as no compensation on either .

Unknown said...

Hello Desmond

Apologies for a delay in replying. Thanks for the clarifications, very very useful.

Desmond Downs said...

No problem :)

urgyen said...

hi desmond

I did the samething which you've explained here that the overexposure occurs when the focus point is moved from white to dark area. But i found there is no over exposure with the dark area under focus point comparing with the lighter one. I use d300 with sb 900. I then tried to check if its because of focus distance and you know what the shot with one meter behind focued is overexposed than shot focued one meter in front.

Desmond Downs said...

Hi Urgyen , a distance difference of 1 meter will make quite a few changes to the output as distance info is still used to a small degree when the flash head is tilted. There are many variables with TTL-BL and you need to be in manual mode and find a place where moving the focus point changes exposure to do this test . Different models behave slightly differently and the D300 may not change exposure as much as my D90 so there will be differences between tests done with different models as well .